Ultimate Fusion Air Dry - Mediums
Antibead - 15ml size bottle
Antibead was designed to put an end to beading which occurs with thin washes when using water to mix paint. It can also be used in thick mixes to help blending and am sure will be useful for many other techniques.
This product has been tested by artists and has had a positive response!
Instructions
Add 1 or more drops until beading stops.
Blendflow - 15ml size bottle
Blendflow has many uses. Use 1 drop in your mixture to help when blending creases and blushes especially when it is a THICK mix. Great for hair and thick mixes. This product adds a gliding/flowing nature to your paint mix. It does take time to dry so only apply the next coat after Blendflow is dry or you will remove the layer beneath. Test for best results. (1 drop in your mixture is sufficient to help glide when painting hair.)
Note - It may add shine with THICK mixes so add a drop of matte concentrate to achieve a matte finish.
Mix Ratio - 1 drop of Blendflow, per (2ml or 6 drops) of water. Add more or less for desired effect.
Drytime extender - 15ml size bottle
Drytime Extender was created for Hair painting when using THICK paint over hours at a time and needing your mixture to not dry up quickly. It will extend the drying time by 3-4 times. Add a few drops to your mix.
Please note - It will add shine so only use a few drops in your mix.
Hair painting TIP... keep wetting your mix in your bowl to keep it alive.
You can use this product to add to paint colours.
Eraser - 15ml size bottle
Please note - Eraser contains traces of Isopropyl, please do not apply over any medium as it will remove it along with the paint.
If you can not remove your mistake with a wet cotton bud or a toothpick. Add a few drops of Eraser to a cotton tip and gently wipe over the area you need paint to be removed. This will help to remove paint. It may not always work and it will be impossible to remove any errors after 24 hours. Seal over area if you find it no longer takes paint.
IMPORTANT - DO NOT USE ERASER over and Gel or polyurethane products such as gloss, satin, 3D Dewy Skin or 3D Hair Effect, it will remove the medium as well as paint.
Matte Extreme - 15ml size bottle
Matte Extreme was designed to apply to vinyl with a wedge in a pouncing action when you wish for a ‘Matte Finish’. Some use a drop in each of their washes for an overall matter skin effect.
You can use this product to add to paint colours and other mediums.
For best results, Pounce using a non latex wedge until area is matte. once touch dry you can apply another round until you reach your desired matte effect.
Gloss varnish - 15ml size bottle
Gloss & Satin Varnish will give a degree of satin or gloss to the area you apply it. This is a last coat. Do not apply directly over powders.
Tip for powders - Seal powders first. Use a small flat brush to apply gloss or Satin to nails lips, inner eye, ear etc (Always clean brushes after use)
This product will take several minutes to dry.
Matte Concentrate - 15ml size bottle
Matte Concentrate was designed to add to THICK mixes when you wish for a ‘Matte Finish’. Some use a drop in each of their washes for an overall matter skin effect. You could also add a drop of Shine Remover to get a similar effect.
You can use this product to add to paint colours and other mediums.
Do not use this product on its own, it is designed to be added to paints and mediums only.
Satin varnish - 15ml size bottle
Gloss & Satin Varnish will give a degree of satin or gloss to the area you apply it. This is a last coat. Do not apply directly over powders.
Tip for powders - Seal powders first. Use a small flat brush to apply gloss or Satin to nails lips, inner eye, ear etc (Always clean brushes after use)
This product will take several minutes to dry.
Shine remover - 15ml size bottle
Shine Remover was designed to correct any shine. Sometime when using THICK mixtures and with some mediums, it can create a dewy look or add shine.
Mixtures with a ratio of Paint to water 1/7 I would suggest using a drop on Matting agent or Shine Remover.
Ultimate Fusion can give a glow to the skin, some use a drop in each of their washes for an overall matter skin effect. You could also add a drop of Shine remover to get a similar effect.
Many have had no shine issues and enjoy using Ultimate Fusion without the need for this product.
You can use this product to add to paint colours and mediums.
Sealer - 15ml size bottle
Sealer as created to use as a barrier between products that are not Ultimate Fusion brand. These include Powders, Genesis etc. It is suggested that you seal over any non-ultimate Fusion product. Genesis sealer is not yet tested.
Sealer can add more translucency to your layers if you add a drop to your mixture. Sealer is Flat. It will leave your work the same way it was before sealer was added.
You can use this product to add to paint colours and mediums.
Thinners - 15ml size bottle
Thinners was designed to act like heat set thinning medium. It is used when you wish to apply a thicker paint. Wet the area before applying your mix to enhance performance for blending. It also slows down Drying time. Use a small brush in a pouncing action to blend creases.
It also slows drying time . Add a few drops to your paint mix.
Please note - It may add shine if using it instead of water, always add a drop of matte concentrate to your mix to stop shine.
(Ratio example 1 paint-5 thinner-1 drop of matte concentrate) Always test, as some vinyls react differently. Add more matte concentrate if needed.
This product can be used in hair painting.
You can use this product to add to paint colours
Blister Lip comes in a 15ml jar
Blister lip is designed to dry a light shade which resembles dry skin. This product dries matte. The applicator is used to move the product around edges of blisters or lip edge to give a realistic impression of dry skin. Also gives a texture when patted on the vinyl. Can be applied over and over to focus on more dry skin in chosen areas.
3D baby dew textured Skin comes in a 15ml jar
I created this product to have the perfect Dewiness that I love to see on real newborn skin. It is my personal favourite product because it boosts the realism of my work.
I use this product neat and use a UF Brand textured sponge ‘torn’ to add a pattern for added depth on the face.
I like a smoother and softer feel on the limbs so I dilute it with (sealer ratio 1:1) and use a UF Brand Wedge for a flat surface)
Tip...Smooth surface....Always use a flat wedge to add no texture for a smooth feel and look.
Instructions for a Matte skin....
Remember, It gives a dewy look so only add Matte Concentrate if you wish for a matte look. (ratio, 3D dewy to matte concentrate 5:1)
You can definitely get quite a few babies out of the jar. It spreads very well.
Creator Tip....
I always add 3D dewy skin last. I find it best to paint hair first before adding 3D dewy skin as I like a silky smooth surface to paint hair strokes on .
I also always clean my kit by wiping down with a wet cloth before adding dewy skin to ensure no dust particles are mixed with the UF product.
This product is air dry and will take several minutes to set, always make sure you replace the lid to keep the product air tight
EMR TOOL - Paint erasing tool
I am very excited to introduce for the first time the newest and original erasing tool bought to you by Ultimate Fusion.
(Eraser & Mark Remover Tool OR the EMR Tool)
The reason this tool is so special is in its ability to remove one or multiple layers of CURED Ultimate Fusion paint. It is also a useful tool during the painting process for difficult to remove marks and very handy for hair painters.
You wont know how you did without it. Definitely a game changer!
See pictures for further description.
Milk Spot Comes in 12ml Bottle
This product has been developed to create realistic milk spots on babies skin. The colour is a perfect dew to matte effect it also is slightly raised so spots look realistic, I have also added my perfect tool which can create the tiniest spots that resemble just born milk spots.
Tip - Use redwine to highlight around larger spots to make them pop.
These products are air dry and will take several minutes before you can paint the next layer, always make sure you replace the lid to keep the product air tight.
Antibead - 15ml size bottle
Antibead was designed to put an end to beading which occurs with thin washes when using water to mix paint. It can also be used in thick mixes to help blending and am sure will be useful for many other techniques.
This product has been tested by artists and has had a positive response!
Instructions
Add 1 or more drops until beading stops.
Blendflow - 15ml size bottle
Blendflow has many uses. Use 1 drop in your mixture to help when blending creases and blushes especially when it is a THICK mix. Great for hair and thick mixes. This product adds a gliding/flowing nature to your paint mix. It does take time to dry so only apply the next coat after Blendflow is dry or you will remove the layer beneath. Test for best results. (1 drop in your mixture is sufficient to help glide when painting hair.)
Note - It may add shine with THICK mixes so add a drop of matte concentrate to achieve a matte finish.
Mix Ratio - 1 drop of Blendflow, per (2ml or 6 drops) of water. Add more or less for desired effect.
Drytime extender - 15ml size bottle
Drytime Extender was created for Hair painting when using THICK paint over hours at a time and needing your mixture to not dry up quickly. It will extend the drying time by 3-4 times. Add a few drops to your mix.
Please note - It will add shine so only use a few drops in your mix.
Hair painting TIP... keep wetting your mix in your bowl to keep it alive.
You can use this product to add to paint colours.
Eraser - 15ml size bottle
Please note - Eraser contains traces of Isopropyl, please do not apply over any medium as it will remove it along with the paint.
If you can not remove your mistake with a wet cotton bud or a toothpick. Add a few drops of Eraser to a cotton tip and gently wipe over the area you need paint to be removed. This will help to remove paint. It may not always work and it will be impossible to remove any errors after 24 hours. Seal over area if you find it no longer takes paint.
IMPORTANT - DO NOT USE ERASER over and Gel or polyurethane products such as gloss, satin, 3D Dewy Skin or 3D Hair Effect, it will remove the medium as well as paint.
Matte Extreme - 15ml size bottle
Matte Extreme was designed to apply to vinyl with a wedge in a pouncing action when you wish for a ‘Matte Finish’. Some use a drop in each of their washes for an overall matter skin effect.
You can use this product to add to paint colours and other mediums.
For best results, Pounce using a non latex wedge until area is matte. once touch dry you can apply another round until you reach your desired matte effect.
Gloss varnish - 15ml size bottle
Gloss & Satin Varnish will give a degree of satin or gloss to the area you apply it. This is a last coat. Do not apply directly over powders.
Tip for powders - Seal powders first. Use a small flat brush to apply gloss or Satin to nails lips, inner eye, ear etc (Always clean brushes after use)
This product will take several minutes to dry.
Matte Concentrate - 15ml size bottle
Matte Concentrate was designed to add to THICK mixes when you wish for a ‘Matte Finish’. Some use a drop in each of their washes for an overall matter skin effect. You could also add a drop of Shine Remover to get a similar effect.
You can use this product to add to paint colours and other mediums.
Do not use this product on its own, it is designed to be added to paints and mediums only.
Satin varnish - 15ml size bottle
Gloss & Satin Varnish will give a degree of satin or gloss to the area you apply it. This is a last coat. Do not apply directly over powders.
Tip for powders - Seal powders first. Use a small flat brush to apply gloss or Satin to nails lips, inner eye, ear etc (Always clean brushes after use)
This product will take several minutes to dry.
Shine remover - 15ml size bottle
Shine Remover was designed to correct any shine. Sometime when using THICK mixtures and with some mediums, it can create a dewy look or add shine.
Mixtures with a ratio of Paint to water 1/7 I would suggest using a drop on Matting agent or Shine Remover.
Ultimate Fusion can give a glow to the skin, some use a drop in each of their washes for an overall matter skin effect. You could also add a drop of Shine remover to get a similar effect.
Many have had no shine issues and enjoy using Ultimate Fusion without the need for this product.
You can use this product to add to paint colours and mediums.
Sealer - 15ml size bottle
Sealer as created to use as a barrier between products that are not Ultimate Fusion brand. These include Powders, Genesis etc. It is suggested that you seal over any non-ultimate Fusion product. Genesis sealer is not yet tested.
Sealer can add more translucency to your layers if you add a drop to your mixture. Sealer is Flat. It will leave your work the same way it was before sealer was added.
You can use this product to add to paint colours and mediums.
Thinners - 15ml size bottle
Thinners was designed to act like heat set thinning medium. It is used when you wish to apply a thicker paint. Wet the area before applying your mix to enhance performance for blending. It also slows down Drying time. Use a small brush in a pouncing action to blend creases.
It also slows drying time . Add a few drops to your paint mix.
Please note - It may add shine if using it instead of water, always add a drop of matte concentrate to your mix to stop shine.
(Ratio example 1 paint-5 thinner-1 drop of matte concentrate) Always test, as some vinyls react differently. Add more matte concentrate if needed.
This product can be used in hair painting.
You can use this product to add to paint colours
Blister Lip comes in a 15ml jar
Blister lip is designed to dry a light shade which resembles dry skin. This product dries matte. The applicator is used to move the product around edges of blisters or lip edge to give a realistic impression of dry skin. Also gives a texture when patted on the vinyl. Can be applied over and over to focus on more dry skin in chosen areas.
3D baby dew textured Skin comes in a 15ml jar
I created this product to have the perfect Dewiness that I love to see on real newborn skin. It is my personal favourite product because it boosts the realism of my work.
I use this product neat and use a UF Brand textured sponge ‘torn’ to add a pattern for added depth on the face.
I like a smoother and softer feel on the limbs so I dilute it with (sealer ratio 1:1) and use a UF Brand Wedge for a flat surface)
Tip...Smooth surface....Always use a flat wedge to add no texture for a smooth feel and look.
Instructions for a Matte skin....
Remember, It gives a dewy look so only add Matte Concentrate if you wish for a matte look. (ratio, 3D dewy to matte concentrate 5:1)
You can definitely get quite a few babies out of the jar. It spreads very well.
Creator Tip....
I always add 3D dewy skin last. I find it best to paint hair first before adding 3D dewy skin as I like a silky smooth surface to paint hair strokes on .
I also always clean my kit by wiping down with a wet cloth before adding dewy skin to ensure no dust particles are mixed with the UF product.
This product is air dry and will take several minutes to set, always make sure you replace the lid to keep the product air tight
EMR TOOL - Paint erasing tool
I am very excited to introduce for the first time the newest and original erasing tool bought to you by Ultimate Fusion.
(Eraser & Mark Remover Tool OR the EMR Tool)
The reason this tool is so special is in its ability to remove one or multiple layers of CURED Ultimate Fusion paint. It is also a useful tool during the painting process for difficult to remove marks and very handy for hair painters.
You wont know how you did without it. Definitely a game changer!
See pictures for further description.
Milk Spot Comes in 12ml Bottle
This product has been developed to create realistic milk spots on babies skin. The colour is a perfect dew to matte effect it also is slightly raised so spots look realistic, I have also added my perfect tool which can create the tiniest spots that resemble just born milk spots.
Tip - Use redwine to highlight around larger spots to make them pop.
These products are air dry and will take several minutes before you can paint the next layer, always make sure you replace the lid to keep the product air tight.
Antibead - 15ml size bottle
Antibead was designed to put an end to beading which occurs with thin washes when using water to mix paint. It can also be used in thick mixes to help blending and am sure will be useful for many other techniques.
This product has been tested by artists and has had a positive response!
Instructions
Add 1 or more drops until beading stops.
Blendflow - 15ml size bottle
Blendflow has many uses. Use 1 drop in your mixture to help when blending creases and blushes especially when it is a THICK mix. Great for hair and thick mixes. This product adds a gliding/flowing nature to your paint mix. It does take time to dry so only apply the next coat after Blendflow is dry or you will remove the layer beneath. Test for best results. (1 drop in your mixture is sufficient to help glide when painting hair.)
Note - It may add shine with THICK mixes so add a drop of matte concentrate to achieve a matte finish.
Mix Ratio - 1 drop of Blendflow, per (2ml or 6 drops) of water. Add more or less for desired effect.
Drytime extender - 15ml size bottle
Drytime Extender was created for Hair painting when using THICK paint over hours at a time and needing your mixture to not dry up quickly. It will extend the drying time by 3-4 times. Add a few drops to your mix.
Please note - It will add shine so only use a few drops in your mix.
Hair painting TIP... keep wetting your mix in your bowl to keep it alive.
You can use this product to add to paint colours.
Eraser - 15ml size bottle
Please note - Eraser contains traces of Isopropyl, please do not apply over any medium as it will remove it along with the paint.
If you can not remove your mistake with a wet cotton bud or a toothpick. Add a few drops of Eraser to a cotton tip and gently wipe over the area you need paint to be removed. This will help to remove paint. It may not always work and it will be impossible to remove any errors after 24 hours. Seal over area if you find it no longer takes paint.
IMPORTANT - DO NOT USE ERASER over and Gel or polyurethane products such as gloss, satin, 3D Dewy Skin or 3D Hair Effect, it will remove the medium as well as paint.
Matte Extreme - 15ml size bottle
Matte Extreme was designed to apply to vinyl with a wedge in a pouncing action when you wish for a ‘Matte Finish’. Some use a drop in each of their washes for an overall matter skin effect.
You can use this product to add to paint colours and other mediums.
For best results, Pounce using a non latex wedge until area is matte. once touch dry you can apply another round until you reach your desired matte effect.
Gloss varnish - 15ml size bottle
Gloss & Satin Varnish will give a degree of satin or gloss to the area you apply it. This is a last coat. Do not apply directly over powders.
Tip for powders - Seal powders first. Use a small flat brush to apply gloss or Satin to nails lips, inner eye, ear etc (Always clean brushes after use)
This product will take several minutes to dry.
Matte Concentrate - 15ml size bottle
Matte Concentrate was designed to add to THICK mixes when you wish for a ‘Matte Finish’. Some use a drop in each of their washes for an overall matter skin effect. You could also add a drop of Shine Remover to get a similar effect.
You can use this product to add to paint colours and other mediums.
Do not use this product on its own, it is designed to be added to paints and mediums only.
Satin varnish - 15ml size bottle
Gloss & Satin Varnish will give a degree of satin or gloss to the area you apply it. This is a last coat. Do not apply directly over powders.
Tip for powders - Seal powders first. Use a small flat brush to apply gloss or Satin to nails lips, inner eye, ear etc (Always clean brushes after use)
This product will take several minutes to dry.
Shine remover - 15ml size bottle
Shine Remover was designed to correct any shine. Sometime when using THICK mixtures and with some mediums, it can create a dewy look or add shine.
Mixtures with a ratio of Paint to water 1/7 I would suggest using a drop on Matting agent or Shine Remover.
Ultimate Fusion can give a glow to the skin, some use a drop in each of their washes for an overall matter skin effect. You could also add a drop of Shine remover to get a similar effect.
Many have had no shine issues and enjoy using Ultimate Fusion without the need for this product.
You can use this product to add to paint colours and mediums.
Sealer - 15ml size bottle
Sealer as created to use as a barrier between products that are not Ultimate Fusion brand. These include Powders, Genesis etc. It is suggested that you seal over any non-ultimate Fusion product. Genesis sealer is not yet tested.
Sealer can add more translucency to your layers if you add a drop to your mixture. Sealer is Flat. It will leave your work the same way it was before sealer was added.
You can use this product to add to paint colours and mediums.
Thinners - 15ml size bottle
Thinners was designed to act like heat set thinning medium. It is used when you wish to apply a thicker paint. Wet the area before applying your mix to enhance performance for blending. It also slows down Drying time. Use a small brush in a pouncing action to blend creases.
It also slows drying time . Add a few drops to your paint mix.
Please note - It may add shine if using it instead of water, always add a drop of matte concentrate to your mix to stop shine.
(Ratio example 1 paint-5 thinner-1 drop of matte concentrate) Always test, as some vinyls react differently. Add more matte concentrate if needed.
This product can be used in hair painting.
You can use this product to add to paint colours
Blister Lip comes in a 15ml jar
Blister lip is designed to dry a light shade which resembles dry skin. This product dries matte. The applicator is used to move the product around edges of blisters or lip edge to give a realistic impression of dry skin. Also gives a texture when patted on the vinyl. Can be applied over and over to focus on more dry skin in chosen areas.
3D baby dew textured Skin comes in a 15ml jar
I created this product to have the perfect Dewiness that I love to see on real newborn skin. It is my personal favourite product because it boosts the realism of my work.
I use this product neat and use a UF Brand textured sponge ‘torn’ to add a pattern for added depth on the face.
I like a smoother and softer feel on the limbs so I dilute it with (sealer ratio 1:1) and use a UF Brand Wedge for a flat surface)
Tip...Smooth surface....Always use a flat wedge to add no texture for a smooth feel and look.
Instructions for a Matte skin....
Remember, It gives a dewy look so only add Matte Concentrate if you wish for a matte look. (ratio, 3D dewy to matte concentrate 5:1)
You can definitely get quite a few babies out of the jar. It spreads very well.
Creator Tip....
I always add 3D dewy skin last. I find it best to paint hair first before adding 3D dewy skin as I like a silky smooth surface to paint hair strokes on .
I also always clean my kit by wiping down with a wet cloth before adding dewy skin to ensure no dust particles are mixed with the UF product.
This product is air dry and will take several minutes to set, always make sure you replace the lid to keep the product air tight
EMR TOOL - Paint erasing tool
I am very excited to introduce for the first time the newest and original erasing tool bought to you by Ultimate Fusion.
(Eraser & Mark Remover Tool OR the EMR Tool)
The reason this tool is so special is in its ability to remove one or multiple layers of CURED Ultimate Fusion paint. It is also a useful tool during the painting process for difficult to remove marks and very handy for hair painters.
You wont know how you did without it. Definitely a game changer!
See pictures for further description.
Milk Spot Comes in 12ml Bottle
This product has been developed to create realistic milk spots on babies skin. The colour is a perfect dew to matte effect it also is slightly raised so spots look realistic, I have also added my perfect tool which can create the tiniest spots that resemble just born milk spots.
Tip - Use redwine to highlight around larger spots to make them pop.
These products are air dry and will take several minutes before you can paint the next layer, always make sure you replace the lid to keep the product air tight.